Aerofly rc 7 playstion 3 controller how to#
Aerofly rc 7 playstion 3 controller full#

A 1/4' 24'X24' piece of HDPE can be purchased online or at a hardware store. It's usually recommended to get at least double the size of your robot. When deciding how big of a sheet to get, you should probably get a fairly big sheet in case you mess up on cutting. When deciding the thickness to get, get about 1/4' thick. This plastic is easy to work with and cheap. For a beginner, it's recommended to use a type of plastic called HDPE. Most robots this size are made out of plastic or aluminum.

A robot needs a chassis to attach all the electronics to. Be sure you get a charger to charge your battery pack with. It will be more expensive by a few dollars, but is an all around better battery to get. If you have to choose between a 1450 mAh battery or a 2000 mAh battery of the same voltage and weight go with the 2000 mAh. For the size of robot you are building, it's recommend about 1800 mAh. The higher you go the better, but the more expensive and usually heavier. Now you need to deal with the capacity of your robot's battery pack. It's usually recommended going with the 6.0V (if your servos can handle it, which most can) because it will allow you to have your servo motor go faster and have more power. Most servos will be fine running on either of those. The most common in robots are 4.8V and 6.0V. You have to pick a voltage for your battery pack. However, they die fast and you have to buy them over and over again. These batteries are common (You probably have some), cheap, and easy to get.

Alkaline batteries are the common batteries that aren't rechargeable.

NiMH batteries are very similar to NiCad batteries in size, weight, and price but have better overall performance and these are the batteries usually recommended for a beginner's project.

Aerofly rc 7 playstion 3 controller full#

The biggest problem with these batteries is if you charge them when they aren't fully dead, they won't last for as long on a full charge.

NiCad batteries are common rechargeable batteries.

Only use this type of battery if you have experience in robots and are willing to spend more money on your robot. However, they are dangerous, expensive, and require a special charger.

Lipo batteries are the newest batteries that you can get and are extremely lightweight.

These are Lithium Polymer (Lipo), NiMH, NiCad, and Alkaline. There are 3 main types of batteries that we will be choosing from.

Choose a battery You will need to get something to power your robot.

Modifying a servo will void the warranty, but it has to be done.

Since the servo can normally only spin 180 degrees you have to modify it so it has continuous rotation.

The HiTec HS-311 servo can be bought here. This servo has a great balance of speed and torque, is inexpensive, and is a good size for this robot. It's recommended to get the Hitec HS-311 servo for the first RC robot. You can always purchase and attach a more powerful or faster servo after you finish building. For this robot, try to get a good balance of speed and torque. You want a high torque, but the higher the torque, generally the lower the speed. If there are no gears and the torque is low, it probably won't allow the robot to move forward because it doesn't have the strength. Size/weight isn't very important in this project because you will probably have plenty of room left over anyway. Make sure the motor is 360 degree modifiable. If the motor is 360 degree modifiable, you can modify it to spin continuously. Since servo motors only turn 180 degrees, your robot would only be able to go forward a little bit. These are speed, torque, size/weight, and if they are 360 Modifiable. There are four basic things you need to worry about when buying servo motors.

Aerofly rc 7 playstion 3 controller how to#

After you understand how to build a remote controlled robot, you may want to make another one (or modify the first one) to use DC motors, rather than servo motors. This project will be using servo motors because it's easier and you don't have to buy an expensive 'speed controller' or a separate gear box. A servo motor is different than a basic DC motor because a servo motor is geared, can only turn 180 degrees, and can transmit data back on it's position. This means to go forward both motors spin forward, to go backwards both motors spin backwards, and to turn one motor goes and one motor stays still. This way you can use the simplest steering method, differential drive. One motor will power one wheel and one for the other.

Choosing a servo motor: To move the robot you will need to use motors.

You will need a material for the chassis, two 'servo' motors, a battery, a transmitter and a receiver. Try to order from as few sites as possible and you sometimes can save money on shipping. But you should choose them now and know where to buy them.